Take a look at the image below. [IMG_8530] I need to get at the black cover nestled behind, and just to the left of, that corrugated metal clad line. To clear that line out of my way, I need to remove a 24mm x 5mm fastener from a banjo fitting. [ https://live.staticflickr.com/65535/54506322250_cf…

Name: Ratchet Extension Drive Bar (1/4″-3/8″DR)
Uploaded: 2025-05-08T21:19:26Z
Description: Would a tool like this work? [Ratchet Extension Drive Bar (1/4″-3/8″DR)] Tester

Would a tool like this work? [Ratchet Extension Drive Bar (1/4″-3/8″DR)] Tester

If you can get a box end wrench on it, smacking a hammer on the wrench shank near the fitting will sometimes break it loose. You can also slip another wrench onto the wrench on the banjo to gain leverage. Same for a breaker bar. Smacking each of them with a hammer can also help break it free.

From the demonstration, I speculate that Ratchet Extension Drive Bar doodad would work. It definitely can reach that banjo fitting bolt head, and ALSO eliminates the wrench swing arc problem. And with a wobble extension btwn that tool and a 24mm 6pt socket, maybe the fastener would relent. Problem …

[image] TITE-REACH 1/2 inch Professional Extension Wrench - Amazon.com TITE-REACH 1/2 inch Professional Extension Wrench - Amazon.com $140.00 Tester

It never occurred to me to smack the shaft of the wrench. I’ll give that a try. Thanks for the tip! I put a long screwdriver on the side of the banjo connector and the bolt, mindful not to damage either with aggressive lateral impacts. Predictably, it had no effect. There is absolutely no room to …

Holy moly! I had absolutely no idea this sort of tool exists! Thanks for suggesting it. Ordered!

Hitting a wrench with a hammer is likely to result in a damaged tool, and unlikely to result in loosening a difficult fastener. And if you can get a wrench onto the fastener, you should be able to get a breaker bar or other means of extending the wrench in order to add leverage. Often times, as a …

I’m pretty certain thwacking a box-end wrench with a hammer is unlikely to result in a damaged tool. It seems a comparatively harmless way to deliver shocks to a stubborn bolt where the head isn’t accessible. Lateral whacks to fasteners is generally not good policy. Maybe this is your point, in whic…

[image] Extension Wrenches & Tools - Specialized for Tight Work Spaces Tite-Reach specialty tools are professional grade hand tools that will make your job easier by reaching those hard to access nuts and bolts. Save your knuckles, save your time! Tester

[image] carburatediron: I’m pretty certain thwacking a box-end wrench with a hammer is unlikely to result in a damaged tool. You are correct, I have beat the crap out of some of my wrenches over the years and never hurt any.. Besides, you can go buy a cheap wrench just for this job and if yo…

Soliciting Suggestions to Remove a Hard-to-Reach Fastener

Maintenance/Repairs

Tester May 8, 2025, 9:19pm 2

Would a tool like this work?

Tester

1 Like

Topic		Replies	Views
Impact wrench technique when access is limited? Maintenance/Repairs	10	18316	November 14, 2012
Low Profile Ratchet and Socket Recommendations Maintenance/Repairs	49	5674	September 28, 2022
Tool advice to remove 2 bolts from Rack to remove and replace Maintenance/Repairs mercury , villager	29	4501	April 26, 2014
Tricks for removing stuck bolts and nuts Maintenance/Repairs	22	20731	March 9, 2012
Recomended tools to remove a bolt with a snaped head? General Discussion	45	7457	February 24, 2017

Soliciting Suggestions to Remove a Hard-to-Reach Fastener

Related topics