# Where can I get brake rotors resurfaced?

**URL:** <https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971>\
**Category:** Maintenance/Repairs\
**Tags:** van, ram, dodge, brakes\
**Created:** [April 5, 2010, 12:50am UTC](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971 "2010-04-05T00:50:12Z")\
**Posts on this page:** 4\
**Page:** 2

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [January 14, 2018, 12:48am UTC](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971/21 "2018-01-14T00:48:58Z")

</div>

If the rotors are within their wear limits, and the shop offers a resurfacing service for a fee that makes sense vs a new rotor, I concur. I’m guessing however that’s not the case in many instances, either b/c of the wear limit restriction, the shop doesn’t offer that service, or the fee they charge makes a new rotor a better bang for the buck. The local repair shop in my area for example does not offer a rotor or drum turning service.

---

<div class="post-metadata">

**Author:** ![db4690](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/db4690/32/2583_2.png) [@db4690](https://community.cartalk.com/u/db4690)\
**Post date:** [January 14, 2018, 12:58am UTC](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971/22 "2018-01-14T00:58:39Z")

</div>

Depending on just how warped a rotor is, you could spend a considerable amount of time cutting it, and by the time it’s acceptable, it’s now just barely above discard thickness

And there’s a very good chance it will be warped again. . . to the point it affects braking ability and is noticeable . . . within a very short time frame. A thin rotor is more likely to warp, versus a brand new rotor, assuming we’re talking about a quality product. Bendix, Wagner, factory rotors, etc

In that case, it would be better to just replace the rotors along with the pads

I can’t speak for anybody else, but if I’m replacing brake pads, and I’m even considering cutting the rotors, I measure runout and rotor thickness. With a few quick calculations, I can determine if it’s a waste of time to cut them. In many cases, I know ahead of time, that I can’t even bring them within specs without going below discard thickness. Or I know it’s going to be very close, so also not worth cutting.

Cutting is not always the answer

---

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [January 14, 2018, 2:41am UTC](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971/23 "2018-01-14T02:41:46Z")

</div>

> [@Chris\_Slaton](#):
>
> I don’t understand why so many of you are quick to replace a good part…resurfacing your rotors is fine as long as they don’t get too thin.

Perhaps because they don’t have access to a brake lathe and would rather buy cheap $20 rotors than pay $10-15 to resurface an $80 rotor.

For the vehicles that I work with I am able resurface about 95% of the rotors. About 5 years ago I had a co-worker that was replacing rotors several times a week. I would take them home after hours, the scrap yard was paying $220 per ton for brake rotors. I stopped and measured a pair of rotors and they were .080" above minimum specs. I think he was just too lazy to machine the rotors and the pay is the same to replace them.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [January 14, 2018, 2:46am UTC](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971/24 "2018-01-14T02:46:18Z")

</div>

I had the rotors resurfaced years ago on my wife’s 99 Camry for around $12 each. New rotors were around $30 each. I had two vehicles in use to save $36. The wife’s car was jacked up awaiting rotors. My truck was ferrying the rotors to and fro from my garage. I guess it depends on how big of a hurry you’re in. This time, I ordered new oem rotors so my wife could drive my car to the grocery store while I worked on hers. In my experience and driving habits, oem brake pads and rotors last 100k miles. I buy oem once at or near 100k. I figure I will only have to replace once. Then at 200k, I’m ready to retire the vehicle anyway.

[Previous page](https://community.cartalk.com/t/where-can-i-get-brake-rotors-resurfaced/46971.md?page=1)
