# Very low power after replacing valve cover gaskets. 2000 Toyota Tundra

**URL:** <https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663>\
**Category:** Maintenance/Repairs\
**Created:** [November 9, 2015, 12:18am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663 "2015-11-09T00:18:14Z")\
**Posts on this page:** 15\
**Page:** 2

<div class="post-metadata">

**Author:** ![ok4450](https://avatars.discourse-cdn.com/v4/letter/o/e9bcb4/32.png) [@ok4450](https://community.cartalk.com/u/ok4450)\
**Post date:** [November 10, 2015, 7:28am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/21 "2015-11-10T07:28:29Z")

</div>

If it ran well before and does not run well now one might suspect an air leak in the intake tract between the MAF sensor and throttle body.  
Any air leak below the throttle body should show up as a rough or slightly rough idle.

---

<div class="post-metadata">

**Author:** ![Yosemite](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/yosemite/32/643_2.png) [@Yosemite](https://community.cartalk.com/u/Yosemite)\
**Post date:** [November 10, 2015, 8:08am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/22 "2015-11-10T08:08:40Z")

</div>

I would side with @VDCDriver. Go back and check your work. It’s easy to forget to plug something in, or reconnect a line somewhere. We’ve all done it!!!

And because you say it did not help with the oil leak…check to make sure some vacuum line or wire did not make it’s way under the valve cover while you were installing it, and it is keeping the cover from tightening down properly.

Yosemite

---

<div class="post-metadata">

**Author:** ![MikeInNH](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@MikeInNH](https://community.cartalk.com/u/MikeInNH)\
**Post date:** [November 10, 2015, 7:45pm UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/23 "2015-11-10T19:45:22Z")

</div>

> **I think just about any V6 Honda Odyssey or Accord, Toyota Camry or Avalon, Lexus ES or RX Series, Ford Taurus from 85-07, and many many others.**

Could be…Since the Honda’s we owned were 4-cylinders…and wifes Lexus has been extremely reliable…no need to examine how the intake manifold is installed. I only work on cars as needed.

Last V6 I did any engine work on was my GMC-S-15…I replaced the valve cover gaskets on that engine at least 4 times. If I had to remove the intake manifold to do that job…I would have sold that pice of cr\*p vehicle a lot sooner then I did.

---

<div class="post-metadata">

**Author:** ![insightful](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/insightful/32/2732_2.png) [@insightful](https://community.cartalk.com/u/insightful)\
**Post date:** [November 11, 2015, 12:28am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/24 "2015-11-11T00:28:57Z")

</div>

> _Never seen a design like that._

Then obviously, it doesn’t exist…

My Insight (4-cyl) requires intake manifold removal for valve cover removal.

---

<div class="post-metadata">

**Author:** ![MikeInNH](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@MikeInNH](https://community.cartalk.com/u/MikeInNH)\
**Post date:** [November 11, 2015, 12:37am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/25 "2015-11-11T00:37:54Z")

</div>

Still waiting!!!

---

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [November 11, 2015, 12:46am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/26 "2015-11-11T00:46:47Z")

</div>

_wifes Lexus has been extremely reliable…no need to examine how the intake manifold is installed. I only work on cars as needed._

If you have ever replaced the spark plugs on that ES350 or your 4Runner you wouldn’t forget the manifold design, someone else must be working on your vehicles.

---

<div class="post-metadata">

**Author:** ![MikeInNH](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@MikeInNH](https://community.cartalk.com/u/MikeInNH)\
**Post date:** [November 11, 2015, 2:08am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/27 "2015-11-11T02:08:36Z")

</div>

> **If you have ever replaced the spark plugs on that ES350 or your 4Runner you wouldn't forget the manifold design, someone else must be working on your vehicles.**

And you’d be dead wrong. Why would I be looking a the intake manifold to replace the spark-plugs?

---

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [November 11, 2015, 7:28am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/28 "2015-11-11T07:28:58Z")

</div>

Removing the coils and spark plugs from the rear bank would be much easier without that large manifold.

---

<div class="post-metadata">

**Author:** ![MikeInNH](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@MikeInNH](https://community.cartalk.com/u/MikeInNH)\
**Post date:** [November 11, 2015, 7:40am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/29 "2015-11-11T07:40:30Z")

</div>

It’s a lot easier when you remove the cross bar in the back.

---

<div class="post-metadata">

**Author:** ![asemaster](https://avatars.discourse-cdn.com/v4/letter/a/5f9b8f/32.png) [@asemaster](https://community.cartalk.com/u/asemaster)\
**Post date:** [November 13, 2015, 1:10am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/30 "2015-11-13T01:10:18Z")

</div>

Just happened to think of this discussion as we were removing the upper intake to replace spark plugs on this 2005 Hyundai.

---

<div class="post-metadata">

**Author:** ![db4690](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/db4690/32/2583_2.png) [@db4690](https://community.cartalk.com/u/db4690)\
**Post date:** [November 13, 2015, 7:38am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/31 "2015-11-13T07:38:17Z")

</div>

@asemaster

Nice picture!

What’s that red thing in the upper left?

Please don’t tell me that’s one of those cheapo low-taste “double” wiper blade assemblies . . . I thought those went out of style in the early- or mid-90s ☹

---

<div class="post-metadata">

**Author:** ![asemaster](https://avatars.discourse-cdn.com/v4/letter/a/5f9b8f/32.png) [@asemaster](https://community.cartalk.com/u/asemaster)\
**Post date:** [November 13, 2015, 8:01am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/32 "2015-11-13T08:01:54Z")

</div>

@db4690 yeah, we were marveling at those wiper blades and thought the same thing…where the heck do you get those things anymore?

After doing the plugs and wires work we moved on to an electronic complaint involving the interior of the car. What did I find? The car has been wrecked and repaired using junkyard parts, including a steering column and steering wheel from a different car, with mismatched wiring. So now when attempting to set or cancel the cruise control the radio will change stations or lower the volume.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [November 13, 2015, 9:43am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/33 "2015-11-13T09:43:06Z")

</div>

Suggest to be careful when changing the radio settings while driving on the freeway. Whatever you don’t, don’t try to adjust the radio clock at 65 mph!! … lol

---

<div class="post-metadata">

**Author:** ![irlandes](https://avatars.discourse-cdn.com/v4/letter/i/b5e925/32.png) [@irlandes](https://community.cartalk.com/u/irlandes)\
**Post date:** [November 16, 2015, 7:38am UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/34 "2015-11-16T07:38:49Z")

</div>

Some good diagnostics on this thread. Good job!

---

<div class="post-metadata">

**Author:** ![tardrex](https://avatars.discourse-cdn.com/v4/letter/t/34f0e0/32.png) [@tardrex](https://community.cartalk.com/u/tardrex)\
**Post date:** [November 20, 2015, 10:40pm UTC](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663/35 "2015-11-20T22:40:08Z")

</div>

A faulty MAF will put the computer in limp mode.  
I recently had the same problem , the RPM`s wouldn`t go above 2,500 rpm`s. I back probed the MAF wires with a volt meter, it had 12.8 volts going in and 0.01 volts coming out on the ground wire and the reference wire going to the computer.I replaced the MAF and the car runs fine now.

[Previous page](https://community.cartalk.com/t/very-low-power-after-replacing-valve-cover-gaskets-2000-toyota-tundra/91663.md?page=1)
