# Scared!

**URL:** <https://community.cartalk.com/t/scared/86805>\
**Category:** Maintenance/Repairs\
**Created:** [August 25, 2014, 7:16am UTC](https://community.cartalk.com/t/scared/86805 "2014-08-25T07:16:09Z")\
**Posts on this page:** 9\
**Page:** 1

<div class="post-metadata">

**Author:** ![Cw400](https://avatars.discourse-cdn.com/v4/letter/c/f08c70/32.png) [@Cw400](https://community.cartalk.com/u/Cw400)\
**Post date:** [August 25, 2014, 7:16am UTC](https://community.cartalk.com/t/scared/86805/1 "2014-08-25T07:16:09Z")

</div>

My 2004 silverado has 116000on the clock and I know it needs new plugs, but I am scared that all that time the plugs have had time to seize in the aluminum heads.  
I am afraid that one or more will tear out the threads resulting in pulling the heads to repair. Do I really need to worry or am I over thinking?  
Is there anything I can do to prevent this or do I just go for broke and deal with whatever happens?

---

<div class="post-metadata">

**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\
**Post date:** [August 25, 2014, 7:27am UTC](https://community.cartalk.com/t/scared/86805/2 "2014-08-25T07:27:26Z")

</div>

Can’t tell unless someone attempts to remove the plugs.

Tester

---

<div class="post-metadata">

**Author:** ![SteveC76](https://avatars.discourse-cdn.com/v4/letter/s/958977/32.png) [@SteveC76](https://community.cartalk.com/u/SteveC76)\
**Post date:** [August 25, 2014, 7:29am UTC](https://community.cartalk.com/t/scared/86805/3 "2014-08-25T07:29:20Z")

</div>

You will be fine, if you had a Ford that would be a problem.

---

<div class="post-metadata">

**Author:** ![Cw400](https://avatars.discourse-cdn.com/v4/letter/c/f08c70/32.png) [@Cw400](https://community.cartalk.com/u/Cw400)\
**Post date:** [August 25, 2014, 7:30am UTC](https://community.cartalk.com/t/scared/86805/4 "2014-08-25T07:30:59Z")

</div>

Why if it was a Ford? What is the difference?

---

<div class="post-metadata">

**Author:** ![MY\_2\_CENTS](https://avatars.discourse-cdn.com/v4/letter/m/22d042/32.png) [@MY\_2\_CENTS](https://community.cartalk.com/u/MY_2_CENTS)\
**Post date:** [August 25, 2014, 7:33am UTC](https://community.cartalk.com/t/scared/86805/5 "2014-08-25T07:33:25Z")

</div>

Be sure it’s dead cold when you do it. If a plug won’t turn don’t force it. Even at that mileage I doubt you will have a problem

---

<div class="post-metadata">

**Author:** ![db4690](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/db4690/32/2583_2.png) [@db4690](https://community.cartalk.com/u/db4690)\
**Post date:** [August 25, 2014, 8:02am UTC](https://community.cartalk.com/t/scared/86805/6 "2014-08-25T08:02:31Z")

</div>

@Cw400‌

Don’t worry. We have tons of gm trucks just like yours in our fleet, and we haven’t really encountered any problems with broken or stuck plugs

Now a Ford would be a different story. Some of the 2V Tritons like to blow the plugs out, taking the female threads and the coil with them. Some of the 3V Tritons have mile-long plugs that often break during removal, unless you have the OTC 6918 removal tool. And if one does break, you’ll more than likely be using a Lisle special tool to extract them.

Moving on . . .

A bit of advice . . . Buy a new set of spark plug wires. They have a particular tendency to break when removing them on your engine. I’m assuming you have either the 5.3 V8 or the 6.0 V8

A colleague . . . non-mechanic . . . asked me for advice before doing the plugs on his 2004 Sierra. I told him to have a fresh wire set on hand, before removing the plugs. He didn’t take my advice. A few days later, he dropped by and said he didn’t have problems replacing the plugs, but after he started the engine, the check engine light came on and there was a clicking noise from one single wire

I gave the cheapskate a good used spark plug wire and sent him on his way. A few days later, he again dropped by and said the clicking had stopped as soon as he replaced that wire.

Hopefully, I was able to answer your questions

---

<div class="post-metadata">

**Author:** ![SteveC76](https://avatars.discourse-cdn.com/v4/letter/s/958977/32.png) [@SteveC76](https://community.cartalk.com/u/SteveC76)\
**Post date:** [August 25, 2014, 7:33pm UTC](https://community.cartalk.com/t/scared/86805/7 "2014-08-25T19:33:37Z")

</div>

Ford has a issue with their spark plug design on the triton motors. You need special tools most of the time due to the plugs breaking in the head.

---

<div class="post-metadata">

**Author:** ![Triedaq](https://avatars.discourse-cdn.com/v4/letter/t/65b543/32.png) [@Triedaq](https://community.cartalk.com/u/Triedaq)\
**Post date:** [August 25, 2014, 8:16pm UTC](https://community.cartalk.com/t/scared/86805/8 "2014-08-25T20:16:33Z")

</div>

One advantage you have with your 2004 Silverado is that the engine sits longitudinally and not transversely. This makes the plugs easier to service.

---

<div class="post-metadata">

**Author:** ![db4690](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/db4690/32/2583_2.png) [@db4690](https://community.cartalk.com/u/db4690)\
**Post date:** [August 26, 2014, 6:20am UTC](https://community.cartalk.com/t/scared/86805/9 "2014-08-26T06:20:07Z")

</div>

@SteveC76

“Ford has a issue with their spark plug design on the triton motors.”

That’s wording it nicely

I would have said “Ford s . . . . . . d the pooch with their spark plug design on the triton motors.”

Have you tried out the OTC 6918 tool yet?
