# Replace cv joint boot with split boot

**URL:** <https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515>\
**Category:** Maintenance/Repairs\
**Created:** [July 31, 2024, 4:00pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515 "2024-07-31T16:00:16Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [July 31, 2024, 4:00pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/1 "2024-07-31T16:00:17Z")

</div>

I have a 2011 Santa Fe with torn inner CV joint boots.  
It seems the consensus is to forget the split-boot repair, let the joint deteriorate, and then replace. I’m pretty sure my boot tear is a new development - little time for contamination. And then, at 240,000 miles the car is near the end of it’s life cycle !  
My question specifically is: has anyone used the type of split boots where the seem gets glued together? Does the bond last ?  
Thanks in advance for reply !

---

<div class="post-metadata">

**Author:** ![LoudThunder](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/loudthunder/32/27769_2.png) [@LoudThunder](https://community.cartalk.com/u/LoudThunder)\
**Post date:** [July 31, 2024, 4:14pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/2 "2024-07-31T16:14:21Z")

</div>

> [@earl.jo.c\_190801](#):
>
> I have a 2011 Santa Fe with torn inner CV joint boots.

**As you wrote, “at 240,000 miles the car is near the end of its life cycle!” So I imagine that the Glue on the "** Split-Boot Repair" would probably outlast your Santa Fe…

---

<div class="post-metadata">

**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\
**Post date:** [July 31, 2024, 4:21pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/3 "2024-07-31T16:21:20Z")

</div>

Split boots are a waste of time and money.

You can never completely clean the old grease/debris out from the CV-joint before installing the split boot, so the CV-joint starts making noise a short time later.

It’s cheaper to keep driving the vehicle with the torn boot until the CV-joint starts making a racket while turning, and then replace the half shaft.

Tester

---

<div class="post-metadata">

**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\
**Post date:** [July 31, 2024, 4:39pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/4 "2024-07-31T16:39:03Z")

</div>

> [@earl.jo.c\_190801](#):
>
> torn **inner** CV joint boots.

Even with a new tear, you have been driving with it slinging (loosing) grease and damaging the inner joint… I agree that most of the time a split boot is a waste of time…

However, the **inner** cv joint will tend to vibrate under acceleration, sometimes harder acceleration and going up hills, it is the outer cv joint that tends to click when turning into parking spots etc etc…

At 240K, I would ride it out until you start getting the vibration and either trade the vehicle or replace the axle assembly, it might last a month, or a year or two…

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [July 31, 2024, 6:48pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/5 "2024-07-31T18:48:30Z")

</div>

Hey Dave,  
I appreciate your insights on what symptoms to expect  
when the inner joint begins to fail, Thanks.

---

<div class="post-metadata">

**Author:** ![bing](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/bing/32/4619_2.png) [@bing](https://community.cartalk.com/u/bing)\
**Post date:** [July 31, 2024, 7:38pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/6 "2024-07-31T19:38:04Z")

</div>

I only tried a split boot once and it didn’t work out.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [July 31, 2024, 10:56pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/7 "2024-07-31T22:56:10Z")

</div>

Diy’er me wouldn’t even try a split boot. I’d replace the boot or the entire half-shaft. I’d do the other side as well. I can’t speak to your Santa Fe’s inner boot, but not that big of a job for my Corolla’s outer boot. If your car is otherwise in good repair, suggest to repair the failed boot, and the other side, the correct way and be done w/it.

Folks here don’t always concur, but I think it is helps extend the life of the CV boots by cleaning off of the grit every now and then. I do that on every oil and filter change, using just a spray of water, and my boots seem to last 150k miles or more. Whatever you do, don’t spray WD 40 or anything else (like solvents) that can deteriorate rubber-like material on the boots. I made that mistake on my VW Rabbit thinking it would prevent water intrusion into the joints, and both front boots failed within just a few thousand miles.

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [August 1, 2024, 12:11pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/8 "2024-08-01T12:11:05Z")

</div>

Hey, thanks to all for your input. I guess I just drive until it fails and then buy some shafts !

---

<div class="post-metadata">

**Author:** ![Cavell](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/cavell/32/43396_2.png) [@Cavell](https://community.cartalk.com/u/Cavell)\
**Post date:** [August 1, 2024, 12:42pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/9 "2024-08-01T12:42:41Z")

</div>

Can you do the work? Can you install a new axle? Do you have the skills? Tools?

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [August 1, 2024, 1:40pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/10 "2024-08-01T13:40:24Z")

</div>

I would do the work myself;  
I doubt any garage around here (north central Illinois) would do a split boot.

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [August 1, 2024, 1:41pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/11 "2024-08-01T13:41:40Z")

</div>

I could possibly do an axel, I’d have to look at some YouTubes and get a feel for it

---

<div class="post-metadata">

**Author:** ![VOLVO-V70](https://avatars.discourse-cdn.com/v4/letter/v/8e8cbc/32.png) [@VOLVO-V70](https://community.cartalk.com/u/VOLVO-V70)\
**Post date:** [August 1, 2024, 1:49pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/12 "2024-08-01T13:49:39Z")

</div>

You said that this thing is close to it’s service life. Why not just start looking and planing to replace it ? Even Kelly Blue Book that usually puts a higher value than other sites has this thing with a low value.

While the CV joints might give you warning that they going to fail if they break it will be most likely at the worst possible time.

---

<div class="post-metadata">

**Author:** ![bing](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/bing/32/4619_2.png) [@bing](https://community.cartalk.com/u/bing)\
**Post date:** [August 1, 2024, 7:19pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/13 "2024-08-01T19:19:03Z")

</div>

I had one fail on the way to work one morning. Just had some vibration. Don’t remember if it was the inner or outer joint now. Made it to work but when I backed up to get into my stall, all the bearings fell out and had to push it the last ten feet.

I had already done a few axles so knew what I needed. 60 miles from home. Was able to tell wife everything I needed and she found everything and brought it to me, including old clothes. Put the new axle in that night in the parking garage and was home by ten. Just have the axle replaced at your convenience.

---

<div class="post-metadata">

**Author:** ![LoudThunder](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/loudthunder/32/27769_2.png) [@LoudThunder](https://community.cartalk.com/u/LoudThunder)\
**Post date:** [August 1, 2024, 9:23pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/14 "2024-08-01T21:23:22Z")

</div>

> [@bing](#):
>
> Put the new axle in that night in the parking garage and was home by ten.

**You changed the axle in the parking lot after work and you had 60-miles to drive home and you were still home by ten?**

**Well then, this song is for You…**

**You don’t tug on Superman’s cape**  
**You don’t spit into the wind**  
**You don’t pull the mask off the old Lone Ranger**  
**And you don’t mess around with Bing…**

---

<div class="post-metadata">

**Author:** ![texases](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/texases/32/862_2.png) [@texases](https://community.cartalk.com/u/texases)\
**Post date:** [August 1, 2024, 9:24pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/15 "2024-08-01T21:24:36Z")

</div>

Was this repair on a Beetle?

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [August 1, 2024, 9:40pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/16 "2024-08-01T21:40:23Z")

</div>

> [@earl.jo.c\_190801](#):
>
> I guess I just drive until it fails and then buy some shafts !

That will work as long as you don’t mine being stranded. The cv joints often give very little warning before they fail, then when they fail, the car won’t move no matter what you do. My only towing experience was for that exact reason, on my VW Rabbit. Happened in the boondocks of far-northern Calif, but fortunately there was a farmhouse nearby, and the folks there kindly phoned for a tow truck in my behalf.

---

<div class="post-metadata">

**Author:** ![bing](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/bing/32/4619_2.png) [@bing](https://community.cartalk.com/u/bing)\
**Post date:** [August 1, 2024, 10:15pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/17 "2024-08-01T22:15:34Z")

</div>

On one of my rivieras. Not my first rodeo but it was in the underground garage, not a parking lot. So I had lights,heat, and the engineers compressor to use. Just like home.

If you drive 120 miles every day you get used to late night repairs.

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [August 1, 2024, 10:22pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/18 "2024-08-01T22:22:56Z")

</div>

are you saying the car had just developed the vibration and then  
shortly thereafter CV joints failed? Its a legit question. I’m used to wheel bearings that fail over several years time - this is my first CV joint issue.  
And as for you wife who you gave the list of tools to and she found them all and delivered them to you, all I can say is you’ve got a true gem there !

---

<div class="post-metadata">

**Author:** ![bing](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/bing/32/4619_2.png) [@bing](https://community.cartalk.com/u/bing)\
**Post date:** [August 1, 2024, 10:25pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/19 "2024-08-01T22:25:46Z")

</div>

I had probably ten miles to go when I noticed the vibration. Forward movement kept the ball bearings in place until I had to reverse to pull into my stall. Then the bearings dropped out of the torn boot. Your results may vary as they say.

---

<div class="post-metadata">

**Author:** ![earl.jo.c\_190801](https://avatars.discourse-cdn.com/v4/letter/e/85e7bf/32.png) [@earl.jo.c\_190801](https://community.cartalk.com/u/earl.jo.c_190801)\
**Post date:** [August 1, 2024, 10:28pm UTC](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515/20 "2024-08-01T22:28:32Z")

</div>

Can’t seem to make this emoticon work , but if I could you’d be seeing a laughing crying face !

[Next page](https://community.cartalk.com/t/replace-cv-joint-boot-with-split-boot/195515.md?page=2)
