# Leaky differential? Would oil wick up dirt?

**URL:** <https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812>\
**Category:** Maintenance/Repairs\
**Created:** [September 27, 2018, 9:02pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812 "2018-09-27T21:02:16Z")\
**Posts on this page:** 20\
**Page:** 2

<div class="post-metadata">

**Author:** ![TwinTurbo](https://avatars.discourse-cdn.com/v4/letter/t/8baadc/32.png) [@TwinTurbo](https://community.cartalk.com/u/TwinTurbo)\
**Post date:** [October 1, 2018, 4:17pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/21 "2018-10-01T16:17:25Z")

</div>

I’ve replaced a number of pinion shaft seals on trucks about this one’s age. The seals only lasts so long and they start weeping. It’s not too hard to replace. Most of mine have been Chevy’s and they use a crush sleeve. That’s the hardest part of the repair IMO, getting that sleeve to compress the right amount. By hand it is very difficult. An air gun makes it a lot easier…

---

<div class="post-metadata">

**Author:** ![RandomTroll](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/randomtroll/32/12184_2.png) [@RandomTroll](https://community.cartalk.com/u/RandomTroll)\
**Post date:** [October 1, 2018, 6:49pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/22 "2018-10-01T18:49:14Z")

</div>

> [@TwinTurbo](#):
>
> That’s the hardest part of the repair IMO, getting that sleeve to compress the right amount.

I have torque wrench. Can you point me to instructions for this? I’ll look, but if you know something that’d be nice. I don’t have a lift so I’d do it on my back.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 1, 2018, 6:53pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/23 "2018-10-01T18:53:08Z")

</div>

I think rtv on the outside is just going to weather / wash off. I’ll have to google a pic of a 1998 Tacoma (I believe you said?) rear differential to understand what you’re explaining on how that thing is assembled.

---

<div class="post-metadata">

**Author:** ![RandomTroll](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/randomtroll/32/12184_2.png) [@RandomTroll](https://community.cartalk.com/u/RandomTroll)\
**Post date:** [October 1, 2018, 6:55pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/24 "2018-10-01T18:55:41Z")

</div>

> [@Scrapyard\_John](#):
>
> I’ll have to google a pic of a 1998 Tacoma

'87 Toyota pickup, 22R, carbureted. For some reason the choice of make & model in these threads doesn’t work for me. I have the Chilton’s and the Haynes.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 1, 2018, 6:58pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/25 "2018-10-01T18:58:37Z")

</div>

As mentioned, they can be real bears to change by hand (pinion seals). Removing the pinion nut is tough. I was unable to remove one on my old CJ5 with an impact. Not enough pressure from the compressor, I guess. So I had a shop do it.

I wouldn’t worry with doing that until I was certain it was leaking there, although it’s not uncommon at all.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 1, 2018, 7:41pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/26 "2018-10-01T19:41:12Z")

</div>

This is from a 1992. Is yours similar?  
image|666x500

There should be a gasket between the carrier (the part with pinion, yoke, etc) and the axle housing (the part that the carrier bolts in/onto). Someone correct me if my terminology is wrong. I believe you’d have to remove the axle shafts in order to seperate those two parts, which could get a little involved. Again, someone correct me if I’m wrong. I’m no expert here, and tend to leave transmissions and differentials alone other than very basic stuff.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 1, 2018, 7:43pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/27 "2018-10-01T19:43:56Z")

</div>

Nice, I can’t see my own picture. Hmmm

 ![image](https://global.discourse-cdn.com/cartalk/original/2X/b/bd5444eedade903ce9fb0f4d3c10a464dc50e7f8.jpeg)

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 1, 2018, 7:44pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/28 "2018-10-01T19:44:59Z")

</div>

There it is. Looks a lot like a Ford 9”, for you hot rodders.

---

<div class="post-metadata">

**Author:** ![RandomTroll](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/randomtroll/32/12184_2.png) [@RandomTroll](https://community.cartalk.com/u/RandomTroll)\
**Post date:** [October 2, 2018, 2:25am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/29 "2018-10-02T02:25:51Z")

</div>

> [@Tester](#):
>
> The differential has some sort of a vent.

Is it that cylinder on the top, a bit to the driver’s side of center, about an inch tall, about ½ inch diameter, a sheet metal cap that moves a bit up and down?

> [@Tester](#):
>
> If it didn’t, when the gears/oil heat up the pressure created would blow out the seals.

Is that permanent damage?

> [@Tester](#):
>
> Make sure that vent isn’t plugged.

I drenched it in mineral spirits and scrubbed it with paper towels; it was clean. I couldn’t blow anything out of it.

> [@Scrapyard\_John](#):
>
> This is from a 1992. Is yours similar?

That looks like it, from the bottom. Is the thing that sticks out on top the vent?

After a closer look today I see the forward side the bolts on the bottom half are oily as are the vanes beneath each. It seems that it leaked out those bolt holes. There’s no new leaking and the drain bolt is as clean and dry, but the leak is really slow.

I’ll have to get a new 24mm socket.

The Chilton’s and the Haynes tell me to check the level by putting my finger in the fill hole and feeling if the oil is within 5mm of the bottom of the hole - really? Who does that? For a finger, it’s a small hole.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 2, 2018, 2:39am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/30 "2018-10-02T02:39:51Z")

</div>

It looks like the vent is underneath the axle in this photo. I’m assuming the axle has the top facing down in the photo. But yes, the vent would come out the top of the axle. I think you can see the end of it in the photo. Should be a little plastic cap on the end of a rubber hose. The other end of the hose attaches to the differential somewhere near the top, but can’t see exactly where in the photo.

As for checking the level, 5 mm from the bottom of the hole isn’t much. If it’s low or you can’t get your finger in the hole (no jokes, please), just add gear oil until it runs out the hole. A few ounces overfilled won’t hurt, especially since it seeps a bit.

Ok, jokes are permitted.

---

<div class="post-metadata">

**Author:** ![RandomTroll](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/randomtroll/32/12184_2.png) [@RandomTroll](https://community.cartalk.com/u/RandomTroll)\
**Post date:** [October 2, 2018, 3:01am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/31 "2018-10-02T03:01:02Z")

</div>

> [@Scrapyard\_John](#):
>
> Should be a little plastic cap on the end of a rubber hose.

It’s a cylinder of solid metal with a sheet metal cap, no rubber hose, no plastic cap. I don’t see those.

> [@Scrapyard\_John](#):
>
> As for checking the level, 5 mm from the bottom of the hole isn’t much.

Really! I can’t even get a finger in and crooked enough to do this, so why recommend it? The owner’s manual says to fill it to overflowing, what I did.

---

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [October 2, 2018, 3:11am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/32 "2018-10-02T03:11:13Z")

</div>

> [@RandomTroll](#):
>
> I’ll have to get a new 24mm socket.

You can use a 15/16" socket.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 2, 2018, 3:14am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/33 "2018-10-02T03:14:14Z")

</div>

Ah, Toyota does the vent a little different apparently.

But the fill and check methods appear universal. Cause er’body wants to stick their finger in a hole.

---

<div class="post-metadata">

**Author:** ![shanonia](https://avatars.discourse-cdn.com/v4/letter/s/9de053/32.png) [@shanonia](https://community.cartalk.com/u/shanonia)\
**Post date:** [October 2, 2018, 3:21am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/34 "2018-10-02T03:21:05Z")

</div>

> [@RandomTroll](#):
>
> It’s a cylinder of solid metal with a sheet metal cap

That’s what I remember from my 1979 Toyota 4X4. I removed it and put in a threaded barb, then ran hose from the barb to a much higher place on the truck.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [October 2, 2018, 3:38am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/35 "2018-10-02T03:38:15Z")

</div>

Seals leaking, drain plug, or plugged vent. More common though is that sometimes the differential metal casing is a little porous and gear oil weeps through a little. Unless the gear oil is low, whatever the cause, when I see it on my truck’s differentials, I just ignore it. When I first bought my truck it was one year old and had a noticeable leak from the rear differential. Definite puddles of gear oil underneath the truck. I had to replace one of the seals to fix that one. Don’t recall which seal it was, but It wasn’t a very difficult job as I recall. The biggest problem I think was all the oil drained out in the process, which made the job a little messy.

---

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [October 2, 2018, 5:50am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/36 "2018-10-02T05:50:55Z")

</div>

Differentials leak for various reasons but porous metal housings is not a common problem in my experience.

When you remove the fill plug and check the level you may find that the loss is insignificant.

---

<div class="post-metadata">

**Author:** ![RandomTroll](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/randomtroll/32/12184_2.png) [@RandomTroll](https://community.cartalk.com/u/RandomTroll)\
**Post date:** [October 2, 2018, 1:13pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/37 "2018-10-02T13:13:43Z")

</div>

> [@shanonia](#):
>
> I removed it and put in a threaded barb, then ran hose from the barb to a much higher place on the truck.

Why?

> [@George\_San\_Jose1](#):
>
> More common though is that sometimes the differential metal casing is a little porous and gear oil weeps through a little.

This is such an astonishing claim that I must not understand it.

> [@George\_San\_Jose1](#):
>
> I had to replace one of the seals to fix that one. Don’t recall which seal it was, but It wasn’t a very difficult job

Hmmm… What is a differential? I think of mine as that ‘pumpkin’ (@Scrapyard\_John 's word), the only seal is where the 2 parts go together, around the circumference. The seal where it attaches to the power shaft, the pinion seal?, requires separating the 2 to maintain, which looks difficult to me, especially lying on my back.

> [@George\_San\_Jose1](#):
>
> The biggest problem I think was all the oil drained out in the process

I’d drain the differential first.

---

<div class="post-metadata">

**Author:** ![Scrapyard-John](https://avatars.discourse-cdn.com/v4/letter/s/f6c823/32.png) [@Scrapyard-John](https://community.cartalk.com/u/Scrapyard-John)\
**Post date:** [October 2, 2018, 2:08pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/38 "2018-10-02T14:08:29Z")

</div>

The pinion seal (the front, where the driveshaft enters), just requires removal of the driveshaft and and yoke (part that connects drive shaft and differential). There will be a seal behind the yoke, on the snout of the differential. The only issue there, is the nut that holds the yoke on (on most differentials) is torqued to 4 billion foot lbs (ok, not really, but it’s tight).

The other seal on your differential, where the differential bolts into the axle housing, requires removal of the axle shafts to seperate the differential from the housing in order to get to the gasket, I think. I’m not 100% sure that the axle shafts have to be removed. It does on a lot of applications. The Toyota axle appears to be built similar to a Ford 9” axle, which was a common swap in the hot rod community. I was hoping someone who had more knowledge than me would chime in as to whether the axle shafts had to be removed (or at least slid outwards) in order to seperate the differential from the housing.

I’d recommend starting with the easiest items. Clean it up and make sure oil isn’t coming from the drain plug, fill plug, or vent/vent tube. Then proceed from there, if you wish. Although, if the truck is driven very little and it’s a very small leak…I might be inclined to leave it, depending on your skills, tools, and work area.

---

<div class="post-metadata">

**Author:** ![shanonia](https://avatars.discourse-cdn.com/v4/letter/s/9de053/32.png) [@shanonia](https://community.cartalk.com/u/shanonia)\
**Post date:** [October 2, 2018, 2:31pm UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/39 "2018-10-02T14:31:28Z")

</div>

> [@RandomTroll](#):
>
> I removed it and put in a threaded barb, then ran hose from the barb to a much higher place on the truck.

It’s a mod I learned from some off-roading magazine. The little spring-loaded valve on the top of the pumpkin can release pressure from inside pumpkin. The heat of operation raises the temp therefore pressure of the air inside. If you cool the pumpkin quickly, like dip it into a lake, the air inside contracts. If the valve does not seal perfectly, water can be drawn in. That’s not good for the long-term health of the gears and bearings.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [October 3, 2018, 1:32am UTC](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812/40 "2018-10-03T01:32:08Z")

</div>

> [@RandomTroll](#):
>
> ‘casing is a little porous’ … This is such an astonishing claim that I must not understand it.

Google 'porous axle casing ', I expect you’ll see some links.

[Previous page](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812.md?page=1)

[Next page](https://community.cartalk.com/t/leaky-differential-would-oil-wick-up-dirt/125812.md?page=3)
