# HVAC Door Motor: Disconnect on 2005 Vibe

**URL:** <https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326>\
**Category:** Maintenance/Repairs\
**Created:** [September 23, 2014, 8:57pm UTC](https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326 "2014-09-23T20:57:29Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Jimbo11](https://avatars.discourse-cdn.com/v4/letter/j/f475e1/32.png) [@Jimbo11](https://community.cartalk.com/u/Jimbo11)\
**Post date:** [September 23, 2014, 8:57pm UTC](https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326/1 "2014-09-23T20:57:29Z")

</div>

My HVAC motor is clacking under the dash–a broken gear from what I’ve read. I currently have the re-circ button pressed in to silence it. Since I can live without re-circulated air, I figured I would just disconnect the motor. I took out the glove compartment, and pulled on what I think is the connection, but can’t get it undone without possibly breaking it off the housing.

Any suggestions? Is there a special tool? Is the connection intended to be a ‘one way’ connection (in only)?

---

<div class="post-metadata">

**Author:** ![knfenimore](https://avatars.discourse-cdn.com/v4/letter/k/9fc348/32.png) [@knfenimore](https://community.cartalk.com/u/knfenimore)\
**Post date:** [September 23, 2014, 10:16pm UTC](https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326/2 "2014-09-23T22:16:17Z")

</div>

Usually the connector has a locking tab you have to push down with your thumb while you pull on the connector at the same time to get it off.

---

<div class="post-metadata">

**Author:** ![ken\_green](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/ken_green/32/816_2.png) [@ken\_green](https://community.cartalk.com/u/ken_green)\
**Post date:** [September 24, 2014, 3:29am UTC](https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326/3 "2014-09-24T03:29:58Z")

</div>

Since you’re into it that far…just get the new blend door acuator and replace it.  
( checking , of course , to see if anything is in there blocking the door movement, causing the gear strip. )

---

<div class="post-metadata">

**Author:** ![Jimbo11](https://avatars.discourse-cdn.com/v4/letter/j/f475e1/32.png) [@Jimbo11](https://community.cartalk.com/u/Jimbo11)\
**Post date:** [September 24, 2014, 9:13pm UTC](https://community.cartalk.com/t/hvac-door-motor-disconnect-on-2005-vibe/87326/4 "2014-09-24T21:13:30Z")

</div>

Thanks for the responses.

From what I’ve read, replacing the blend door actuator may involve removing the dash, and that’s a bit much for me. Also, I looked/felt for a locking tab, and can’t locate. I’m gettin new tires in Nov-maybe one of the tech’s at the shop will be able to do this without much effort.
