# Engine with no compression **URL:** \ **Category:** Maintenance/Repairs\ **Tags:** accord-cpe, engines, accord, honda\ **Created:** [May 3, 2023, 2:25am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406 "2023-05-03T02:25:12Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:25am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/1 "2023-05-03T02:25:12Z")
Looking for recommendations on next steps on repairing my 2 dr honda accord 4 cyl vtec. Backstory: The timing had jumped on the vehicle so i had replaced the head _heard mixed answers on weather or not the 4 cyl vtec was a non interference or an interference motor_ so i ended up replacing the head just to be safe plus also had a head gasket leak anyway so just replaced it entirely. Got a used head from a salvage yeard from a running vehicle and got entirely new head gasket kit and replaced all of the gaskets as well as set timing. Problem at hand: After setting the head, timing and reassembling the motor went for the first turn over… got 1 loud blow back from the exhaust then nothing. From there i went back to the basics of checking for spark, fuel, and compression. After checking the spark and fuel decided to replace the spark plugs and distributor with brand new parts just to be sure. After posting a video of the vehicle turning over in an accord specific forum only answer i got was that it sounded like it had no compression. My questions/concerns: Is there a possibilty the head is not sealing to the block creating the compression loss? The new head gasket was thin metal and i am afraid of its malubility in order to fill any scratches or small gaps. Would i be better off doing a silicone gasket? What is the possibility that the compression loss is coming from the cylinder rings? I am willing to do what ever it takes to repair this vehicle _has too much sentimental value_ but would rather DIY the repair for the experience. Not a mechanical professional but i know my way around replacing parts pretty well. ---
**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\ **Post date:** [May 3, 2023, 2:34am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/2 "2023-05-03T02:34:18Z")
> [@Dom.mayer2002\_185088](#): > > Is there a possibilty the head is not sealing to the block creating the compression loss? Did you check the replacement head for flatness with a precision straight edge and feeler gauge before installing it? Tester ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:37am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/3 "2023-05-03T02:37:14Z")
No, surface was never precision tested for flatness nor was it ever resurfaced. A friend recommended getting it resurfaced but said it wasnt required to be done so i skipped it due tk being young, dumb, and broke. ---
**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\ **Post date:** [May 3, 2023, 2:38am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/4 "2023-05-03T02:38:29Z")
Did you reuse the old head bolts? Tester ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:39am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/5 "2023-05-03T02:39:31Z")
I tried both head bolts from the old head as well as head bolts from the used head. All were torqued to spec as well. ---
**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\ **Post date:** [May 3, 2023, 2:42am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/6 "2023-05-03T02:42:12Z")
The head bolts are a torque to yield stretch bolts, they require replacing every time the head is removed… Did you install the timing belt correctly?? Did you do a compression test to verify compression?? ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:44am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/7 "2023-05-03T02:44:10Z")
Okay. So a good next step to take would be getting brand new head bolts due to possibilty of current bolts being stretched and not getting a true torque? And yes, from what ive heard its hard to mess up timing on the 4 cyl, ive reset timing at least 20 times as well as had multiple people check to make sure it was correct. ---
**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\ **Post date:** [May 3, 2023, 2:47am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/8 "2023-05-03T02:47:54Z")
What timing are you resetting?? Distributor (ignition timing)?? or valve to piston timing (timing belt from crankshaft to camshaft)?? ---
**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\ **Post date:** [May 3, 2023, 2:50am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/9 "2023-05-03T02:50:23Z")
Those two statements say you took two torpedoes into the side of your ship and it sunk. Anyone who’s worked with Honda engines knows, you never install a used head either from the original engine or from a different engine without checking flatness (run-out) first. Because when aluminum heads are removed, they can warp due to locked in stresses. And you never reuse the head bolts because they’re torque-to-yield bolts. And can only be used once. So, you’ll have to start all over again Tester ---
**Author:** ![MikeInNH](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@MikeInNH](https://community.cartalk.com/u/MikeInNH)\ **Post date:** [May 3, 2023, 2:50am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/10 "2023-05-03T02:50:46Z")
I think it could be the timing belt. ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:50am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/11 "2023-05-03T02:50:55Z")
Resetting the the cam to crank timing. ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:51am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/12 "2023-05-03T02:51:35Z")
All belts on the motor have been replaced brand new. ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:53am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/13 "2023-05-03T02:53:46Z")
Okay. I currently already have the head removed. I should start with resurfacing head and getting brand new head bolts? ---
**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\ **Post date:** [May 3, 2023, 2:54am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/14 "2023-05-03T02:54:51Z")
Resetting it means you had to correct it right?? If the timing belt was off you probably bent a valve… ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 2:57am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/15 "2023-05-03T02:57:54Z")
No i was resetting due to failure to start. I was restting the timing before i got opinions about compression loss. Thought i had spark, fuel, and compression since i had redone gaskets, checked fuel, and replaced all spark. I made sure to triple check timing via videos and pictures and had father check as well before motor was turned over every time. ---
**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\ **Post date:** [May 3, 2023, 2:58am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/16 "2023-05-03T02:58:20Z")
If you are unable to check for flatness (runout), then yes. Do you have a torque angle gauge? ![image](https://global.discourse-cdn.com/cartalk/original/3X/4/9/49ee65c54b40f4c1978a6d4eccf15e7d31ac8ea5.jpeg) If not, you’re going to need one for the new head bolts. Tester ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 3:00am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/17 "2023-05-03T03:00:26Z")
I do not but i am not new to renting odd ball tools from auto zone. I will definitely look into the tool and getting a tool to check run out on the head. ---
**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\ **Post date:** [May 3, 2023, 3:02am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/18 "2023-05-03T03:02:44Z")
You need to probably send the head to a machine shop and have it decked and checked, and possibly have a valve job done while it is there… Then you need to buy a book on how to rebuild a Honda engine and read it cover to cover so you understand why and what everything does… And if you didn’t use the tool Tester just showed, what was the torque spec you used?? And do you even know the proper torque sequence?? ---
**Author:** ![Tester](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/tester/32/15976_2.png) [@Tester](https://community.cartalk.com/u/Tester)\ **Post date:** [May 3, 2023, 3:04am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/19 "2023-05-03T03:04:24Z")
[![](https://global.discourse-cdn.com/cartalk/original/3X/8/c/8cb622a8686e2e9b553ca8e84763b07061b4d8b4.jpeg "Cylinder head inspection for flatness / warping") ](https://www.youtube.com/watch?v=u4SzK_OjAkY) Tester ---
**Author:** ![Dom.mayer2002\_185088](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@Dom.mayer2002\_185088](https://community.cartalk.com/u/Dom.mayer2002_185088)\ **Post date:** [May 3, 2023, 3:04am UTC](https://community.cartalk.com/t/engine-with-no-compression/190406/20 "2023-05-03T03:04:31Z")
Yes, i got all of my torque specs and torque sequencing from the vehicles online repair manual. And torque spec i used was just a standard torque wrench torqed to ft/lbs [Next page](https://community.cartalk.com/t/engine-with-no-compression/190406.md?page=2)