# Anti- lock brake light

**URL:** <https://community.cartalk.com/t/anti-lock-brake-light/5311>\
**Category:** Maintenance/Repairs\
**Created:** [September 30, 2007, 4:59pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311 "2007-09-30T16:59:20Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![oldsmobile](https://avatars.discourse-cdn.com/v4/letter/o/c2a13f/32.png) [@oldsmobile](https://community.cartalk.com/u/oldsmobile)\
**Post date:** [September 30, 2007, 4:59pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/1 "2007-09-30T16:59:20Z")

</div>

98 olds intrigue 3.8L v6 150,000 automatic  
  
 my anti lock/brake light comes on my dashboard shortly after i start it and drive off. it happens when the car goes through its diagnostic test. usually within 10 seconds of driving the car.  
  
 i have no diagnostic machine. what would be the most common problem? thanks  
  
 “anti-lock brake code” c1264 i took the car to a local shop and he tested it on his machine and said for some reason the correct amperage is not getting/coming from the rear of the car. he said the alternator is putting out like it should. he said he checked amperage other places and couldn’t find any problem. brakes have 50% life left, no loose wires. i don’t know what else to check. could the battery be going bad?

---

<div class="post-metadata">

**Author:** ![MG-McAnick](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/mg-mcanick/32/188_2.png) [@MG-McAnick](https://community.cartalk.com/u/MG-McAnick)\
**Post date:** [September 30, 2007, 5:57pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/2 "2007-09-30T17:57:29Z")

</div>

It is more than likely that one of the ABS sensors has gotten too much roadside crud on it and is no longer sensing. I’ve cleaned off several of them and they’ve worked again. Has anyone done any brake work on this vehicle lately? Sometimes that will set a code.

---

<div class="post-metadata">

**Author:** ![oldsmobile](https://avatars.discourse-cdn.com/v4/letter/o/c2a13f/32.png) [@oldsmobile](https://community.cartalk.com/u/oldsmobile)\
**Post date:** [September 30, 2007, 7:04pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/3 "2007-09-30T19:04:36Z")

</div>

i have unplupped the sensor wire at each wheel and pluged them back in, they seem ok and are not dirty or corroded.  
i hear a noise under the dash that makes a couple of clicks just before the anti- lock brake light comes on.  
there was no brake work done latly. the shop i went to had all the wheels off and said they looked things over.  
this also caused my cruise control to not work. my cruise control comes on, but will not engage.

---

<div class="post-metadata">

**Author:** ![oldsmobile](https://avatars.discourse-cdn.com/v4/letter/o/c2a13f/32.png) [@oldsmobile](https://community.cartalk.com/u/oldsmobile)\
**Post date:** [October 1, 2007, 7:05pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/4 "2007-10-01T19:05:29Z")

</div>

anyone got any answers for me?

---

<div class="post-metadata">

**Author:** ![willey](https://avatars.discourse-cdn.com/v4/letter/w/a9adbd/32.png) [@willey](https://community.cartalk.com/u/willey)\
**Post date:** [October 1, 2007, 9:26pm UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/5 "2007-10-01T21:26:49Z")

</div>

First of all the alternator and battery have nothing to do with the speed sensor circuit because the sensors generate their own voltage signal. More than likely the speed sensor is defective.

---

<div class="post-metadata">

**Author:** ![oldsmobile](https://avatars.discourse-cdn.com/v4/letter/o/c2a13f/32.png) [@oldsmobile](https://community.cartalk.com/u/oldsmobile)\
**Post date:** [October 2, 2007, 12:33am UTC](https://community.cartalk.com/t/anti-lock-brake-light/5311/6 "2007-10-02T00:33:01Z")

</div>

good info, thanks! is the speed sensor easily replaced, or should i take it to a shop. i am ok about removing and replacing, like brakes and whatnot. could i handle this? does it require special tools?
