# A friend's 2011 Accord, 2.4L, AT is presenting quite a challenge

**URL:** <https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949>\
**Category:** Maintenance/Repairs\
**Created:** [February 2, 2025, 4:42am UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949 "2025-02-02T04:42:08Z")\
**Posts on this page:** 6\
**Page:** 4

<div class="post-metadata">

**Author:** ![Nevada\_545](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/nevada_545/32/41232_2.png) [@Nevada\_545](https://community.cartalk.com/u/Nevada_545)\
**Post date:** [February 12, 2025, 5:36am UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/61 "2025-02-12T05:36:26Z")

</div>

Didn’t you perform a throttle plate relearn after installing the throttle body? You stated you did so in post # 21.

> [@Fresno-Jack](#):
>
> Put it thru the idle relearn procedure after installing new FP, but idle still higher than expected.

---

<div class="post-metadata">

**Author:** ![davesmopar](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/davesmopar/32/41750_2.png) [@davesmopar](https://community.cartalk.com/u/davesmopar)\
**Post date:** [February 12, 2025, 1:23pm UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/62 "2025-02-12T13:23:50Z")

</div>

Did you ever check what the ECT is showing with the KOEO and overnight cold, or at least 3 hours not running? Should be about what the ambient temp is…

---

<div class="post-metadata">

**Author:** ![Fresno-Jack](https://avatars.discourse-cdn.com/v4/letter/f/53a042/32.png) [@Fresno-Jack](https://community.cartalk.com/u/Fresno-Jack)\
**Post date:** [February 12, 2025, 2:00pm UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/63 "2025-02-12T14:00:59Z")

</div>

> [@Nevada\_545](#):
>
> Didn’t you perform a throttle plate relearn after installing the throttle body? You stated you did so in post # 21.

Idle relearn procedure is different from an ECM/PCM reset. ECM/PCM reset is a reprogramming of the car’s computer, which can only be done with Honda’s i-HDS Diagnostic Software and J2534 Reprogramming Software thru a suitable Vehicle Communication Device (VCI) that is compliant with SAE J2534-1 and J2534-2… or so I’m told.

---

<div class="post-metadata">

**Author:** ![Fresno-Jack](https://avatars.discourse-cdn.com/v4/letter/f/53a042/32.png) [@Fresno-Jack](https://community.cartalk.com/u/Fresno-Jack)\
**Post date:** [February 12, 2025, 2:29pm UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/64 "2025-02-12T14:29:47Z")

</div>

> [@davesmopar](#):
>
> Did you ever check what the ECT is showing with the KOEO

Yes, my apologies for not reporting the results of that. After the car sat overnight without starting the ECT temp was the same as ambient temp.

---

<div class="post-metadata">

**Author:** ![Fresno-Jack](https://avatars.discourse-cdn.com/v4/letter/f/53a042/32.png) [@Fresno-Jack](https://community.cartalk.com/u/Fresno-Jack)\
**Post date:** [February 14, 2025, 2:44am UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/65 "2025-02-14T02:44:17Z")

</div>

I tried to edit the title to indicate that I solved the problem and I inadvertently created a new thread. davesmopar suggested I should put my reply in this thread and I agree, so here it is again:

SOLVED! After much poking and prodding and repeated futile attempts to bring down the high idle using the “idle relearn procedure” I finally succeeded. It was only after I unplugged and replugged the Accelerator Pedal Position Sensor that the idle relearn procedure had the desired effect.This may be coincidental, and there may have been some other reason for my success, but it was only after doing this that my efforts paid off.

---

<div class="post-metadata">

**Author:** ![Fresno-Jack](https://avatars.discourse-cdn.com/v4/letter/f/53a042/32.png) [@Fresno-Jack](https://community.cartalk.com/u/Fresno-Jack)\
**Post date:** [February 14, 2025, 5:35pm UTC](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949/66 "2025-02-14T17:35:28Z")

</div>

Found this when looking up info on the accelerator pedal position sensor:

["A faulty accelerator pedal position sensor](https://www.carparts.com/blog/bad-accelerator-pedal-position-sensor-symptoms-and-replacement) can make an idling engine run at higher revolutions per minute (RPM) than expected."

Apparently the fault was not with the accelerator pedal position sensor, but with the wiring connector. The effect, however, was the same. I am surprised that the accelerator pedal position sensor did not show up in a single search I did for causes of a high idle condition.

[Previous page](https://community.cartalk.com/t/a-friends-2011-accord-2-4l-at-is-presenting-quite-a-challenge/198949.md?page=3)
