# 2007 ford taurus loses power about every 9 seconds

**URL:** <https://community.cartalk.com/t/2007-ford-taurus-loses-power-about-every-9-seconds/83901>\
**Category:** Maintenance/Repairs\
**Created:** [February 24, 2014, 4:05am UTC](https://community.cartalk.com/t/2007-ford-taurus-loses-power-about-every-9-seconds/83901 "2014-02-24T04:05:48Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![mwoolf](https://avatars.discourse-cdn.com/v4/letter/m/58956e/32.png) [@mwoolf](https://community.cartalk.com/u/mwoolf)\
**Post date:** [February 24, 2014, 4:05am UTC](https://community.cartalk.com/t/2007-ford-taurus-loses-power-about-every-9-seconds/83901/1 "2014-02-24T04:05:48Z")

</div>

Pretty much like clockwork. Every 9 seconds the power dies for about 1 second and then comes back on. Sometimes the Theft light comes on.

If I am at idle, the car dies.

No check engine light. The car has had all new ignition parts in the last year except battery and alternator.

Any ideas?

---

<div class="post-metadata">

**Author:** ![jgree142](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/jgree142/32/2043_2.png) [@jgree142](https://community.cartalk.com/u/jgree142)\
**Post date:** [February 24, 2014, 10:14pm UTC](https://community.cartalk.com/t/2007-ford-taurus-loses-power-about-every-9-seconds/83901/2 "2014-02-24T22:14:14Z")

</div>

My initial thought was that the PCM is going offline based on the theft lamp illumination. Ford PCMs can go offline for a few reasons.

- Vpwr interruption to the module. (This is the ignition switched feed to module)
- B+ interruption to module.
- Mainsupply voltage being too low or too high.
- Vref shorted to ground (Vref is the regulated 5.0v reference used to power the module cpu and engine compartment sensors. This includes the DPFE, IAT, CHT/ECT, TP, Fuel tank pressure sensor. Intermittent shorts to the Vref circuit will cause the PCM to go offline until the short is eliminated. (DPFEs are very common for this… I am NOT TELLING you to replace this. Someone needs to do some testing.)
- Module failure (Do not replace this without proper diag)

Recommendations:  
All modules will **NEED** scanned for DTCs before any work is performed. (Just because the engine light is not on, does not mean that the PCM has not identified and stored a DTC)

If no codes are present, I would typically then connect a scan tool to the vehicle and would then evaluate the PCM live data display. While in live data display, information like RPM, TP v, IAT v, CHT/ECT v, sync, Vpwr,Vbatt, Key state, Start enabled/disabled and evaluate this parameters during the event. If the live data is lost during the event, that is a really good sign that the module has gone offline. (This is how I would do it when equipped with diagnostic equipment… Not sure what you have available or how hands on you are.)

At that point I would connect a DVOM or o-scope to the VREF circuit and would watch for voltage high/low concerns. (Vref should be 5.0V) if dropping low during the stall/stumble, I would begin to isolate the components using the vref one at a time checking to see if the condition is eliminated. V-ref shorts can happen in the sensors, issues can happen within the wiring harness.

If vref is going low, you cannot forget about base powers and grounds to the pcm. I can write a book here on how to chase this down, it all depends on how hands on you are and what tools you have.
