# 2006 Toyota Solara won't start

**URL:** <https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556>\
**Category:** Maintenance/Repairs\
**Created:** [September 11, 2016, 6:20pm UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556 "2016-09-11T18:20:38Z")\
**Posts on this page:** 10\
**Page:** 2

<div class="post-metadata">

**Author:** ![the\_same\_mountainbike](https://avatars.discourse-cdn.com/v4/letter/t/c89c15/32.png) [@the\_same\_mountainbike](https://community.cartalk.com/u/the_same_mountainbike)\
**Post date:** [September 14, 2016, 12:40am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/21 "2016-09-14T00:40:02Z")

</div>

If it’s spinning as if there’s no compression and then try to start like there is compression, the starter’s gear may not be properly engaging with the flywheel’s ring gear to turn the crankshaft. That’s a starter-assembly internal problem. You can’t tell anything just by looking at it unless you know what to look for.

The other possibility is that the flywheel ring gear is missing some teeth… and the starter motor gear is occasionally hitting the spaces where the teeth used to be, spinning freely before catching a tooth. Honestly, since the starter motor circuit seems to be enabling properly, this would be my guess. It suggests that the Bendix assembly that engages the gears AND closes contacts that enable the starter motor is functioning. A knowledgeable mechanic will have to inspect the flywheel ring gear as a colleague slowly turns the crankshaft.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [September 14, 2016, 2:21am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/22 "2016-09-14T02:21:36Z")

</div>

fyi, I’ve experienced something like this w/my truck when it had a problem where it was leaking fuel into the intake manifold, causing it to flood out. When this happened, it sounded like it had low compression during cranking, then eventually it would pop and run ok, with full power. I think the compression was always fine, but something about the intake manifold being saturated with gas made it sound or at least seem like it had low compression. After I fixed the flooding problem, now it sounds like it always has during cranking.

---

<div class="post-metadata">

**Author:** ![redneckred](https://avatars.discourse-cdn.com/v4/letter/r/50afbb/32.png) [@redneckred](https://community.cartalk.com/u/redneckred)\
**Post date:** [September 14, 2016, 2:25am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/23 "2016-09-14T02:25:14Z")

</div>

I pulled the covers off the timing belt cover and discovered the belt is intact. However, there is a lot of fiber debry from where the outside edge of the belt appears to be wearing out. I think the belt may have jumped time, but I am unsure at this point. I need to find my socket and tool to remove the crankshaft to check the timing to be sure.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [September 14, 2016, 2:38am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/24 "2016-09-14T02:38:49Z")

</div>

On my Corolla anyway as long as you can see the camshaft pulley(s), no need to do anything with the crankshaft to verify the valve timing. Just place the crankshaft at TDC. The camshaft alignment marks should then also line up. If not, rotate the engine 360 degrees and check again. You might be at TDC on the exhaust stroke. The crankshaft has to be at TDC on the compression stroke for the camshaft marks to align correctly.

---

<div class="post-metadata">

**Author:** ![redneckred](https://avatars.discourse-cdn.com/v4/letter/r/50afbb/32.png) [@redneckred](https://community.cartalk.com/u/redneckred)\
**Post date:** [September 14, 2016, 2:41am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/25 "2016-09-14T02:41:28Z")

</div>

I need to pull the crank pulley to get to my timing mark for the crank. I can see both cam shafts but can’t see the crank mark to determine TDC.

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [September 14, 2016, 2:49am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/26 "2016-09-14T02:49:12Z")

</div>

If that’s what you got to do, I guess you have to do it. When you reinstall the crank pulley make a mark on it where TDC is, then next time this extra job won’t be necessary. fyi, it’s often a pretty big job to remove the crank pulley. If you haven’t done it before, suggest you ask here for some pointers before attempting this the first time.

---

<div class="post-metadata">

**Author:** ![redneckred](https://avatars.discourse-cdn.com/v4/letter/r/50afbb/32.png) [@redneckred](https://community.cartalk.com/u/redneckred)\
**Post date:** [September 14, 2016, 2:51am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/27 "2016-09-14T02:51:35Z")

</div>

I have replaced the timing belt on 3 other cars I have owned in the past. This is the easiest one I have done thus far. It has only required 3 sockets (4 if you count the one for the crank pulley).

---

<div class="post-metadata">

**Author:** ![George\_San\_Jose1](https://avatars.discourse-cdn.com/v4/letter/g/e5b9ba/32.png) [@George\_San\_Jose1](https://community.cartalk.com/u/George_San_Jose1)\
**Post date:** [September 14, 2016, 2:55am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/28 "2016-09-14T02:55:51Z")

</div>

Your Solara has a V6 oriented with the long axis of the vehicle then? The timing belt job on that configuration seems to be a little easier to do compared to the transverse mounted I4 configuration, from the comments we get here. Not so much engine and transmission mount involvement I guess.

---

<div class="post-metadata">

**Author:** ![texases](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/texases/32/862_2.png) [@texases](https://community.cartalk.com/u/texases)\
**Post date:** [September 14, 2016, 3:20am UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/29 "2016-09-14T03:20:19Z")

</div>

It’s a traNSverse engine.

---

<div class="post-metadata">

**Author:** ![insightful](https://sea1.discourse-cdn.com/cartalk/user_avatar/community.cartalk.com/insightful/32/2732_2.png) [@insightful](https://community.cartalk.com/u/insightful)\
**Post date:** [September 14, 2016, 8:32pm UTC](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556/30 "2016-09-14T20:32:02Z")

</div>

> [@texases](#):
>
> It’s a traverse engine.

When did Chevy start selling engines to Toyota?

Oh…_transverse_ engine…

;-]

[Previous page](https://community.cartalk.com/t/2006-toyota-solara-wont-start/95556.md?page=1)
