# 2001dodge ram misfire on 1

**URL:** <https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162>\
**Category:** Maintenance/Repairs\
**Created:** [September 14, 2014, 10:18am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162 "2014-09-14T10:18:10Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![kdw](https://avatars.discourse-cdn.com/v4/letter/k/9de0a6/32.png) [@kdw](https://community.cartalk.com/u/kdw)\
**Post date:** [September 14, 2014, 10:18am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/1 "2014-09-14T10:18:10Z")

</div>

I have a misfire on 1 I recently changed intake and plenum gasket, changed plug, wire, injector, cap, rotor, compression check and pulled valve cover rockers moving good and I recently swapped injector wires on 1&3 only shows misfire on 1 anyone have ideas help please

---

<div class="post-metadata">

**Author:** ![kdw](https://avatars.discourse-cdn.com/v4/letter/k/9de0a6/32.png) [@kdw](https://community.cartalk.com/u/kdw)\
**Post date:** [September 14, 2014, 10:19am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/2 "2014-09-14T10:19:12Z")

</div>

This is 5.9 gas

---

<div class="post-metadata">

**Author:** ![ok4450](https://avatars.discourse-cdn.com/v4/letter/o/e9bcb4/32.png) [@ok4450](https://community.cartalk.com/u/ok4450)\
**Post date:** [September 14, 2014, 10:26am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/3 "2014-09-14T10:26:01Z")

</div>

What was the compression number?

---

<div class="post-metadata">

**Author:** ![kdw](https://avatars.discourse-cdn.com/v4/letter/k/9de0a6/32.png) [@kdw](https://community.cartalk.com/u/kdw)\
**Post date:** [September 14, 2014, 10:29am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/4 "2014-09-14T10:29:10Z")

</div>

100-105

---

<div class="post-metadata">

**Author:** ![kdw](https://avatars.discourse-cdn.com/v4/letter/k/9de0a6/32.png) [@kdw](https://community.cartalk.com/u/kdw)\
**Post date:** [September 14, 2014, 10:30am UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/5 "2014-09-14T10:30:48Z")

</div>

Not sure Gage 100% accurate other cylinders about same

---

<div class="post-metadata">

**Author:** ![ok4450](https://avatars.discourse-cdn.com/v4/letter/o/e9bcb4/32.png) [@ok4450](https://community.cartalk.com/u/ok4450)\
**Post date:** [September 14, 2014, 7:18pm UTC](https://community.cartalk.com/t/2001dodge-ram-misfire-on-1/87162/6 "2014-09-14T19:18:49Z")

</div>

You have a problem if that number is accurate. Good numbers even on a worn engine should be in the 175 or better range. The general rule of thumb on compression is 20 X the compression ratio. There will be variances based on altitude and barometric pressure, engine wear, and so on.

If you revisit the compression issue you should do a wet test. This means a small squirt of oil into each cylinder before it’s retested. If the number takes a substantial jump upwards there’s a ring problem. If the number remains the same or only increases slightly then it’s a cylinder head valve issue.
